Electrolux washer
showing HO SE
HO SE is Electrolux's reversed hose detection.
Mon–Sat, 8am–8pm
- Water supply
- Water inlet valve repair
- Source: Electrolux
Book a visit
Three short steps, about a minute.
or call (844) 398-5711
Loading appointment form…
The appointment form couldn’t load. Please try again.
What HO SE
actually means.
HO SE is Electrolux's reversed hose detection. The display shows HO, then SE, then 0 min for 60 seconds, repeating, when the washer senses hot water on the cold inlet and cold on the hot.
Electrolux washer display · also shown as HOSE
What to do when HO SE shows on the washerKind of codeWater supply
Water arrived too slowly, not at all, or kept coming after it should have stopped. The supply valves on the wall and the screens inside the fill hoses are checked before the inlet valve or the level sensor.
Usually leads toWater inlet valve repair
A washer that will not fill, fills slowly, fills with only cold water or keeps filling, repaired at the inlet valve and its screens.
Shows up asWasher Not Filling
The washer starts, hums or clicks, but little or no water comes into the tub, or it fills very slowly.
MakeElectrolux
Full-size front-load washers from the Swedish group, commonly bought as a set with an Electrolux dryer.
SourceElectrolux Owner Center: front loading washer Error Code HO SE reversed hose detection
Electrolux front-load washers with reversed hose detection.
Before you book,
in this order.
Each step comes from Electrolux's own guidance for HO SE on its washers. Follow it to the end: the last card says whether this is a visit.
Press Cancel to acknowledge the alert.
Turn off both supply valves.
Swap the hoses so each goes to the matching inlet, open the valves and restart.
Still there?
It usually turns into water inlet valve repair. Book with the code and the model number.
What not to do
HO SE is not a leak or a valve problem. The water is arriving; it is just going to the wrong side.
What you may
notice with it.
The washer problems HO SE tends to arrive with. Answer these at the washer before anyone is booked.
All problems
Washer Not Filling
5 causes, cheapest first
Where HO SE usually leads
Water inlet valve repair.
Electrolux
washers.
Full-size front-load washers from the Swedish group, commonly bought as a set with an Electrolux dryer.
Electrolux washer repairMore Electrolux codes
Water supply on other makes
Front-load washer
A horizontal drum behind a sealed glass door, a rubber boot, a locking latch and a pump with a filter you can reach from the front.
Stackable washer
The washer at the bottom of a stacked pair or a single-frame laundry center, repaired inside the closet or recess it was sized for.
Compact washer
The 24-inch front-loaders and all-in-one washer-dryers found in apartments, condos and under counters, repaired on their washing side.
In Electrolux's own words
LED will display “HO” followed by “SE” and then the remaining cycle time (0 min) for 60 seconds and then repeat.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Electrolux front-load washers with reversed hose detection.
Electrolux HO SE washer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about HO SE.
Can I clear HO SE myself?
Why does my Electrolux flash HO SE and 0 min over and over?
Do I need a technician for HO SE on my Electrolux?
Back to your everyday
Still showing HO SE?
Book with the code as it appears, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.