Electrolux washer
showing E35
E35 means the pressure sensor is reading water overfill.
Mon–Sat, 8am–8pm
- Water supply
- Water inlet valve repair
- Source: Electrolux
Book a visit
Three short steps, about a minute.
or call (844) 398-5711
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E35
actually means.
E35 means the pressure sensor is reading water overfill. Electrolux calls it a known installation issue and gives two owner steps: clear the code with Cancel, or do a hard reset by unplugging.
Electrolux washer display
What to do when E35 shows on the washerKind of codeWater supply
Water arrived too slowly, not at all, or kept coming after it should have stopped. The supply valves on the wall and the screens inside the fill hoses are checked before the inlet valve or the level sensor.
Usually leads toWater inlet valve repair
A washer that will not fill, fills slowly, fills with only cold water or keeps filling, repaired at the inlet valve and its screens.
Shows up asWasher Overflowing
The washer keeps filling past the normal level, and water spills over the tub, out of the door or onto the floor.
MakeElectrolux
Full-size front-load washers from the Swedish group, commonly bought as a set with an Electrolux dryer.
SourceElectrolux Owner Center: front loading washer Error Code E35 pressure sensor indicates water overfill
Electrolux front-load washers with an LED display.
Before you book,
in this order.
Each step comes from Electrolux's own guidance for E35 on its washers. Follow it to the end: the last card says whether this is a visit.
Press Cancel to clear E35, then press Start to resume the cycle.
If that does not work, unplug the washer, plug it back in, and restart the cycle.
If water ever reaches the floor, shut the supply valves; book a visit if E35 keeps returning.
Still there?
It usually turns into water inlet valve repair. Book with the code and the model number.
What not to do
E35 is not the same as an ordinary slow drain. The washer believes there is too much water, which is why a recently installed or moved washer should be checked by the installer.
What you may
notice with it.
The washer problems E35 tends to arrive with. Answer these at the washer before anyone is booked.
All problems
Where E35 usually leads
Water inlet valve repair.
Electrolux
washers.
Full-size front-load washers from the Swedish group, commonly bought as a set with an Electrolux dryer.
Electrolux washer repairMore Electrolux codes
Water supply on other makes
Front-load washer
A horizontal drum behind a sealed glass door, a rubber boot, a locking latch and a pump with a filter you can reach from the front.
Stackable washer
The washer at the bottom of a stacked pair or a single-frame laundry center, repaired inside the closet or recess it was sized for.
Compact washer
The 24-inch front-loaders and all-in-one washer-dryers found in apartments, condos and under counters, repaired on their washing side.
In Electrolux's own words
Error Code E35 indicates the washing machine pressure sensor is Indicating water overfill.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Electrolux front-load washers with an LED display.
Electrolux E35 washer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E35.
Can I clear E35 myself?
Can I just press Cancel when my Electrolux shows E35?
Why would a new Electrolux show E35?
Back to your everyday
Still showing E35?
Book with the code as it appears, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.