Fisher & Paykel washer
showing no tAP
no tAP means water is not getting into the washer.
Mon–Sat, 8am–8pm
- Water supply
- Water inlet valve repair
- Source: Fisher & Paykel
Book a visit
Three short steps, about a minute.
or call (844) 398-5711
Loading appointment form…
The appointment form couldn’t load. Please try again.
What no tAP
actually means.
no tAP means water is not getting into the washer.
Fisher & Paykel washer display
What to do when no tAP shows on the washerKind of codeWater supply
Water arrived too slowly, not at all, or kept coming after it should have stopped. The supply valves on the wall and the screens inside the fill hoses are checked before the inlet valve or the level sensor.
Usually leads toWater inlet valve repair
A washer that will not fill, fills slowly, fills with only cold water or keeps filling, repaired at the inlet valve and its screens.
Shows up asWasher Not Filling
The washer starts, hums or clicks, but little or no water comes into the tub, or it fills very slowly.
MakeFisher & Paykel
A New Zealand appliance maker whose washers are a small part of its US range next to kitchen products.
SourceFisher & Paykel WH2424F and WH2424P front loading washer installation and user guide, US/CA (PDF on fisherpaykel.com)
Fisher & Paykel WH2424F and WH2424P 24-inch front loaders (US/CA user guide 429798D); the code is spelled out on the display.
Before you book,
in this order.
Each step comes from Fisher & Paykel's own guidance for no tAP on its washers. Follow it to the end: the last card says whether this is a visit.
Make sure the faucets are turned on.
Check that the cold hose goes to the cold valve and the hot hose to the hot valve.
Clean the inlet hose filters and straighten any kinks.
Check the drain hose is not too low or pushed too far into the standpipe, which can siphon water out.
Still there?
It usually turns into water inlet valve repair. Book with the code and the model number.
What not to do
no tAP does not always mean no water pressure; a siphoning drain hose can empty the drum as it fills.
What you may
notice with it.
The washer problems no tAP tends to arrive with. Answer these at the washer before anyone is booked.
All problems
Where no tAP usually leads
Water inlet valve repair.
Fisher & Paykel
washers.
A New Zealand appliance maker whose washers are a small part of its US range next to kitchen products.
Fisher & Paykel washer repairMore Fisher & Paykel codes
Water supply on other makes
Front-load washer
A horizontal drum behind a sealed glass door, a rubber boot, a locking latch and a pump with a filter you can reach from the front.
Top-load washer
The upright washer with a lid on top, moving clothes either with a tall central agitator or with a low impeller plate in the bottom of the basket.
In Fisher & Paykel's own words
Check the faucets have been turned on.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Fisher & Paykel WH2424F and WH2424P 24-inch front loaders (US/CA user guide 429798D); the code is spelled out on the display.
Fisher & Paykel no tAP washer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about no tAP.
Can I clear no tAP myself?
Why does my Fisher & Paykel show no tAP with the faucets open?
How deep can the drain hose go before it causes no tAP on a Fisher & Paykel?
Back to your everyday
Still showing no tAP?
Book with the code as it appears, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.