Whirlpool washer
showing F8 E1
F8 E1 means the control expected more water than it measured during fill.
Mon–Sat, 8am–8pm
- Water supply
- Water inlet valve repair
- Source: Whirlpool
Book a visit
Three short steps, about a minute.
or call (844) 398-5711
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F8 E1
actually means.
F8 E1 means the control expected more water than it measured during fill. Whirlpool traces it to supply valves that are not fully open, kinked or clogged hoses, dirty inlet screens, flood-stop devices that lower the pressure, and a drain hose installed so that it siphons water out while the tub fills.
Whirlpool washer display · also shown as F8E1, Lo FL, LF
What to do when F8 E1 shows on the washerKind of codeWater supply
Water arrived too slowly, not at all, or kept coming after it should have stopped. The supply valves on the wall and the screens inside the fill hoses are checked before the inlet valve or the level sensor.
Usually leads toWater inlet valve repair
A washer that will not fill, fills slowly, fills with only cold water or keeps filling, repaired at the inlet valve and its screens.
Shows up asWasher Not Filling
The washer starts, hums or clicks, but little or no water comes into the tub, or it fills very slowly.
MakeWhirlpool
A leading American washer brand, in agitator and impeller top-loaders, front-loaders and stacked laundry centers.
SourceWhirlpool product help: F8 E1 (top-load washer)
Whirlpool top-load and front-load washers; some front-load models show Lo FL and some top-load models show LF for the same fill problem.
Before you book,
in this order.
Each step comes from Whirlpool's own guidance for F8 E1 on its washers. Follow it to the end: the last card says whether this is a visit.
Open both the hot and the cold supply valves all the way; this design expects both hoses connected and carrying water.
If the door or lid is locked and the panel ignores you, press Power and let the washer finish its drain routine of roughly 8 to 10 minutes.
Check both fill hoses for kinks, then shut the valves and clean the small inlet screens where the hoses meet the washer.
If F8 E1 returns with good pressure and clean screens, book a visit.
Still there?
It usually turns into water inlet valve repair. Book with the code and the model number.
What not to do
It is not a sign that the washer is short of detergent or that the load is too big. The code is about how much water arrived, so the checks all sit between the house valves and the washer.
What you may
notice with it.
The washer problems F8 E1 tends to arrive with. Answer these at the washer before anyone is booked.
All problems
Washer Not Filling
5 causes, cheapest first
Where F8 E1 usually leads
Water inlet valve repair.
Whirlpool
washers.
A leading American washer brand, in agitator and impeller top-loaders, front-loaders and stacked laundry centers.
Whirlpool washer repairMore Whirlpool codes
Water supply on other makes
Front-load washer
A horizontal drum behind a sealed glass door, a rubber boot, a locking latch and a pump with a filter you can reach from the front.
Top-load washer
The upright washer with a lid on top, moving clothes either with a tall central agitator or with a low impeller plate in the bottom of the basket.
Stackable washer
The washer at the bottom of a stacked pair or a single-frame laundry center, repaired inside the closet or recess it was sized for.
In Whirlpool's own words
The F8 E1 error code means your washer is not detecting the correct amount of incoming water.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Whirlpool top-load and front-load washers; some front-load models show Lo FL and some top-load models show LF for the same fill problem.
Whirlpool F8 E1 washer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F8 E1.
Can I clear F8 E1 myself?
Why won't my Whirlpool respond to buttons after F8 E1?
I only wash in cold water. Can a closed hot valve cause F8 E1 on a Whirlpool?
Back to your everyday
Still showing F8 E1?
Book with the code as it appears, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.