Whirlpool washer
showing F7 E1
F7 E1 is a motor speed sensing code: the control commanded a speed and the motor did not get there.
Mon–Sat, 8am–8pm
- Drive motor
- Drive motor and belt repair
- Source: Whirlpool
Book a visit
Three short steps, about a minute.
or call (844) 398-5711
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F7 E1
actually means.
F7 E1 is a motor speed sensing code: the control commanded a speed and the motor did not get there. On a front-load Whirlpool that was recently installed, shipping bolts left in the back are the first thing the manufacturer names.
Whirlpool washer display · also shown as F7E1
What to do when F7 E1 shows on the washerKind of codeDrive motor
The control told the drum to turn and it did not turn as expected — a slipped or broken belt, a worn coupler, or a motor or its speed sensor reading out of range. The belt and the connections are checked before the motor.
Usually leads toDrive motor and belt repair
A drum that hums without turning, a burning rubber smell or a spin that never reaches speed, traced to the belt, the coupling, the motor or its control.
Shows up asWasher Not Spinning
The wash finishes but the drum barely turns at the end, and the clothes come out dripping wet.
MakeWhirlpool
A leading American washer brand, in agitator and impeller top-loaders, front-loaders and stacked laundry centers.
SourceWhirlpool product help: F7E1 (front-load washer)
Whirlpool front-load washers (shipping bolt check) and top-load washers, where Whirlpool offers only a power reset for the code.
Before you book,
in this order.
Each step comes from Whirlpool's own guidance for F7 E1 on its washers. Follow it to the end: the last card says whether this is a visit.
On a newly installed front-load model, check the back panel for all four shipping bolts and their plastic spacers and remove any that are still there.
Take out part of the load if the drum is packed tight.
Unplug the washer for 5 minutes, then run a Drain & Spin; if F7 E1 comes back, book a visit.
Still there?
It usually turns into drive motor and belt repair. Book with the code and the model number.
What not to do
It does not by itself mean the motor is burned out. The code reports the speed the control measured, which a drag on the drum or a wiring problem can also produce.
What you may
notice with it.
The washer problems F7 E1 tends to arrive with. Answer these at the washer before anyone is booked.
All problems
Washer Not Spinning
5 causes, cheapest first
Where F7 E1 usually leads
Drive motor and belt repair.
Whirlpool
washers.
A leading American washer brand, in agitator and impeller top-loaders, front-loaders and stacked laundry centers.
Whirlpool washer repair
Front-load washer
A horizontal drum behind a sealed glass door, a rubber boot, a locking latch and a pump with a filter you can reach from the front.
Top-load washer
The upright washer with a lid on top, moving clothes either with a tall central agitator or with a low impeller plate in the bottom of the basket.
Stackable washer
The washer at the bottom of a stacked pair or a single-frame laundry center, repaired inside the closet or recess it was sized for.
In Whirlpool's own words
This code indicates a motor speed sensing error, the motor can not achieve the correct speed for the cycle selection.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Whirlpool front-load washers (shipping bolt check) and top-load washers, where Whirlpool offers only a power reset for the code.
Whirlpool F7 E1 washer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F7 E1.
Can I clear F7 E1 myself?
My new Whirlpool front-loader showed F7 E1 on its first load. Why?
Is it safe to keep running a Whirlpool that shows F7 E1?
Back to your everyday
Still showing F7 E1?
Book with the code as it appears, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.