Whirlpool washer
showing F6 E2
F6 E2 points to trouble between the main control unit, the user interface on the console and the wiring that links them.
Mon–Sat, 8am–8pm
- Communication
- Controls and sensors
- Source: Whirlpool
Book a visit
Three short steps, about a minute.
or call (844) 398-5711
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F6 E2
actually means.
F6 E2 points to trouble between the main control unit, the user interface on the console and the wiring that links them. Whirlpool describes it as a reboot alert and gives only a power reset as the owner step.
Whirlpool washer display · also shown as F6E2
What to do when F6 E2 shows on the washerKind of codeCommunication
The main control board and the panel board have lost contact with each other. The wire harness and its plugs are checked, and any sign of water reaching them, before either board is replaced.
Usually leads toControls and sensors
A dead display, buttons that do nothing, cycles that stop at random or codes that keep returning, traced to the control, its sensors or its wiring.
Shows up asControl Panel Not Responding
The washer's buttons or dial do nothing, the display freezes or goes blank, or settings will not change.
MakeWhirlpool
A leading American washer brand, in agitator and impeller top-loaders, front-loaders and stacked laundry centers.
SourceWhirlpool product help: F6E2 (top-load washer)
Whirlpool top-load and front-load washers with a two-part F/E display.
Before you book,
in this order.
Each step comes from Whirlpool's own guidance for F6 E2 on its washers. Follow it to the end: the last card says whether this is a visit.
Unplug the washer, or switch off its breaker, for 5 minutes.
Restore power and start a short cycle.
If F6 E2 appears again, book a visit; the boards and the harness between them are tested inside the console.
What not to do
F6 E2 is not caused by the load, the water supply or the drain. It is an electronics code, so hose and detergent checks will not change it.
What you may
notice with it.
The washer problems F6 E2 tends to arrive with. Answer these at the washer before anyone is booked.
All problems
Control Panel Not Responding
5 causes, cheapest first
Where F6 E2 usually leads
Controls and sensors.
Whirlpool
washers.
A leading American washer brand, in agitator and impeller top-loaders, front-loaders and stacked laundry centers.
Whirlpool washer repairMore Whirlpool codes
Communication on other makes
Front-load washer
A horizontal drum behind a sealed glass door, a rubber boot, a locking latch and a pump with a filter you can reach from the front.
Top-load washer
The upright washer with a lid on top, moving clothes either with a tall central agitator or with a low impeller plate in the bottom of the basket.
Stackable washer
The washer at the bottom of a stacked pair or a single-frame laundry center, repaired inside the closet or recess it was sized for.
In Whirlpool's own words
The F6 E2 alert indicates there is an issue with the appliance control unit, user interface, or associated wiring.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Whirlpool top-load and front-load washers with a two-part F/E display.
Whirlpool F6 E2 washer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F6 E2.
Can I clear F6 E2 myself?
Will a power reset clear F6 E2 on a Whirlpool for good?
Which part usually fixes F6 E2 on a Whirlpool?
Back to your everyday
Still showing F6 E2?
Book with the code as it appears, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.