Maytag washer
showing F0 E3
F0 E3 means the Maytag judged the load too heavy and started an overload recovery routine.
Mon–Sat, 8am–8pm
- Unbalanced load
- Suspension and shock repair
- Source: Maytag
Book a visit
Three short steps, about a minute.
or call (844) 398-5711
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F0 E3
actually means.
F0 E3 means the Maytag judged the load too heavy and started an overload recovery routine. A packed or lopsided tub can also finish with a reduced spin and wet clothes.
Maytag washer display · also shown as F0E3
What to do when F0 E3 shows on the washerKind of codeUnbalanced load
The control sensed the drum wobbling and cut the spin short. Usually it is one heavy item bunched to one side or a machine that is not level; worn shocks or springs come next, and shipping bolts left in a new washer are checked too.
Usually leads toSuspension and shock repair
A washer that shakes, bangs the cabinet or walks across the floor on the spin, repaired at the shocks, springs, rods and feet.
Shows up asWasher Shaking and Walking
The washer shakes hard, thumps against the wall or creeps across the floor during the spin.
MakeMaytag
Full-size top-load and front-load washers from a brand owned by Whirlpool and built on shared platforms.
SourceMaytag product help: F0E3 - Overload (top-load washer)
Maytag top-load washers with a two-part F/E display.
Before you book,
in this order.
Each step comes from Maytag's own guidance for F0 E3 on its washers. Follow it to the end: the last card says whether this is a visit.
Let the recovery cycle finish, then take some items out.
Load dry clothes in loose heaps evenly around the basket wall rather than packing them down.
Put small items in mesh bags so they cannot slip into the pump, and book a visit if F0 E3 appears with normal loads.
Still there?
It usually turns into suspension and shock repair. Book with the code and the model number.
What not to do
F0 E3 does not mean the motor has failed. It is the washer protecting itself from weight it was not built to spin.
What you may
notice with it.
The washer problems F0 E3 tends to arrive with. Answer these at the washer before anyone is booked.
All problems
Washer Shaking and Walking
5 causes, cheapest first
Where F0 E3 usually leads
Suspension and shock repair.
Maytag
washers.
Full-size top-load and front-load washers from a brand owned by Whirlpool and built on shared platforms.
Maytag washer repair
Front-load washer
A horizontal drum behind a sealed glass door, a rubber boot, a locking latch and a pump with a filter you can reach from the front.
Top-load washer
The upright washer with a lid on top, moving clothes either with a tall central agitator or with a low impeller plate in the bottom of the basket.
Stackable washer
The washer at the bottom of a stacked pair or a single-frame laundry center, repaired inside the closet or recess it was sized for.
In Maytag's own words
The load is too heavy. The overload recovery cycle is running.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Maytag top-load washers with a two-part F/E display.
Maytag F0 E3 washer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F0 E3.
Can I clear F0 E3 myself?
My Maytag shows F0 E3 with a normal-looking load. Why?
Can I add clothes after the Maytag starts without causing F0 E3?
Back to your everyday
Still showing F0 E3?
Book with the code as it appears, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.