Maytag washer
showing Int
Int shows after a cycle is paused or canceled on a Maytag front-loader.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: Maytag
Book a visit
Three short steps, about a minute.
or call (844) 398-5711
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Int
actually means.
Int shows after a cycle is paused or canceled on a Maytag front-loader. The drum can take 20 to 30 minutes to stop spinning and drain, and the code stays on the display during that time.
Maytag washer display
What to do when Int shows on the washerKind of codeMode, not a failure
Something the washer does by design, or a setting somebody turned on — a child lock, a prompt to run a cleaning cycle, a paused cycle waiting for the door. No part has failed and nothing needs replacing.
Usually leads toNo repair
Give the washer up to half an hour to stop and drain.
Shows up asWasher Stops Mid-Cycle
The washer starts normally, then pauses, stalls or shuts off before the cycle ends, sometimes with water still inside.
MakeMaytag
Full-size top-load and front-load washers from a brand owned by Whirlpool and built on shared platforms.
SourceMaytag product help: Int code (front-load washer)
Maytag front-load washers; the steps to clear the code differ by model.
Before you book,
in this order.
Each step comes from Maytag's own guidance for Int on its washers. Follow it to the end: the last card says whether this is a visit.
Give the washer up to half an hour to stop and drain.
To clear the display, press Pause or Cancel twice and then Power once; the method varies by model.
If Int stays on after draining finishes and the buttons do nothing, book a visit.
Cleared?
No part had to be replaced. If a later load stops with water left in the drum or the cycle halts again, treat it as a new problem.
What not to do
Int is not a report that something broke. It appears because someone paused or canceled the cycle.
What you may
notice with it.
The washer problems Int tends to arrive with. Answer these at the washer before anyone is booked.
All problems
Washer Stops Mid-Cycle
5 causes, cheapest first
No repair indicated
Nothing to repair.
Something the washer does by design, or a setting somebody turned on — a child lock, a prompt to run a cleaning cycle, a paused cycle waiting for the door. No part has failed and nothing needs replacing.
Maytag
washers.
Full-size top-load and front-load washers from a brand owned by Whirlpool and built on shared platforms.
Maytag washer repairMore Maytag codes
Mode, not a failure on other makes
Front-load washer
A horizontal drum behind a sealed glass door, a rubber boot, a locking latch and a pump with a filter you can reach from the front.
Top-load washer
The upright washer with a lid on top, moving clothes either with a tall central agitator or with a low impeller plate in the bottom of the basket.
Stackable washer
The washer at the bottom of a stacked pair or a single-frame laundry center, repaired inside the closet or recess it was sized for.
In Maytag's own words
This error code indicates that the cycle was paused or canceled.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Maytag front-load washers; the steps to clear the code differ by model.
Maytag Int washer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Int.
Can I clear Int myself?
Why does my Maytag show Int when I only paused it?
How long should Int stay on my Maytag's display?
Back to your everyday
Still showing Int?
Book with the code as it appears, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.