Maytag washer
showing F8 E3
On a Maytag front-loader, F8 E3 means the washer saw too much water or too much foam inside.
Mon–Sat, 8am–8pm
- Water supply
- Water inlet valve repair
- Source: Maytag
Book a visit
Three short steps, about a minute.
or call (844) 398-5711
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F8 E3
actually means.
On a Maytag front-loader, F8 E3 means the washer saw too much water or too much foam inside. Maytag's steps all deal with foam: non-HE or overdosed detergent and thickened bleach are the causes it names.
Maytag washer display · also shown as F8E3
What to do when F8 E3 shows on the washerKind of codeWater supply
Water arrived too slowly, not at all, or kept coming after it should have stopped. The supply valves on the wall and the screens inside the fill hoses are checked before the inlet valve or the level sensor.
Usually leads toWater inlet valve repair
A washer that will not fill, fills slowly, fills with only cold water or keeps filling, repaired at the inlet valve and its screens.
Shows up asWasher Overflowing
The washer keeps filling past the normal level, and water spills over the tub, out of the door or onto the floor.
MakeMaytag
Full-size top-load and front-load washers from a brand owned by Whirlpool and built on shared platforms.
SourceMaytag product help: F8 E3 (front-load washer)
Maytag front-load washers with a two-part F/E display.
Before you book,
in this order.
Each step comes from Maytag's own guidance for F8 E3 on its washers. Follow it to the end: the last card says whether this is a visit.
Switch to HE detergent and measure it; with very soft water, use less.
Stop using splash-less or easy-pour thickened chlorine bleach and use a regular liquid bleach.
Run a Clean Washer cycle with the drum empty; book a visit if F8 E3 shows with correct detergent, or if water ever reaches the floor.
Still there?
It usually turns into water inlet valve repair. Book with the code and the model number.
What not to do
F8 E3 is not the same as a leak on the floor. It reports what is inside the tub; any water outside the washer means shutting the supply valves first.
What you may
notice with it.
The washer problems F8 E3 tends to arrive with. Answer these at the washer before anyone is booked.
All problems
Where F8 E3 usually leads
Water inlet valve repair.
Maytag
washers.
Full-size top-load and front-load washers from a brand owned by Whirlpool and built on shared platforms.
Maytag washer repairMore Maytag codes
Water supply on other makes
Front-load washer
A horizontal drum behind a sealed glass door, a rubber boot, a locking latch and a pump with a filter you can reach from the front.
Top-load washer
The upright washer with a lid on top, moving clothes either with a tall central agitator or with a low impeller plate in the bottom of the basket.
Stackable washer
The washer at the bottom of a stacked pair or a single-frame laundry center, repaired inside the closet or recess it was sized for.
In Maytag's own words
The overflow condition occurs if there is too much water or foam in the washer.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Maytag front-load washers with a two-part F/E display.
Maytag F8 E3 washer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F8 E3.
Can I clear F8 E3 myself?
Can bleach cause F8 E3 on my Maytag?
I use HE detergent and still get F8 E3 on my Maytag. What next?
Back to your everyday
Still showing F8 E3?
Book with the code as it appears, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.