LG washer
showing FE
FE means the washer detected more water in the tub than it should hold.
Mon–Sat, 8am–8pm
- Water supply
- Water inlet valve repair
- Source: LG
Book a visit
Three short steps, about a minute.
or call (844) 398-5711
Loading appointment form…
The appointment form couldn’t load. Please try again.
What FE
actually means.
FE means the washer detected more water in the tub than it should hold. LG points to extra water coming in through the dispenser or a water valve that does not close.
LG washer display · also shown as E04, E12
What to do when FE shows on the washerKind of codeWater supply
Water arrived too slowly, not at all, or kept coming after it should have stopped. The supply valves on the wall and the screens inside the fill hoses are checked before the inlet valve or the level sensor.
Usually leads toWater inlet valve repair
A washer that will not fill, fills slowly, fills with only cold water or keeps filling, repaired at the inlet valve and its screens.
Shows up asWasher Overflowing
The washer keeps filling past the normal level, and water spills over the tub, out of the door or onto the floor.
MakeLG
Front-load and top-load washers from the Korean maker, known for direct-drive motors and detailed error codes.
SourceLG US Help Library: LG front load washer error code list (Wayback copy, 7 Sep 2026)
LG front-load washers; the current list pairs FE with E04 and E12. LG's older list adds that a machine with a bad inlet valve may fill even when turned off.
Before you book,
in this order.
Each step comes from LG's own guidance for FE on its washers. Follow it to the end: the last card says whether this is a visit.
Close both water faucets right away.
Unplug the washer for 60 seconds, then start a quick program and confirm it begins by draining.
If the tub keeps filling or FE returns, leave the faucets closed and book a visit.
Still there?
It usually turns into water inlet valve repair. Book with the code and the model number.
What not to do
FE is not a slow-fill message; that is IE. FE is about too much water, which can end on the floor.
What you may
notice with it.
The washer problems FE tends to arrive with. Answer these at the washer before anyone is booked.
All problems
Washer Overflowing
5 causes, cheapest first
Where FE usually leads
Water inlet valve repair.
LG
washers.
Front-load and top-load washers from the Korean maker, known for direct-drive motors and detailed error codes.
LG washer repairMore LG codes
Water supply on other makes
Front-load washer
A horizontal drum behind a sealed glass door, a rubber boot, a locking latch and a pump with a filter you can reach from the front.
Top-load washer
The upright washer with a lid on top, moving clothes either with a tall central agitator or with a low impeller plate in the bottom of the basket.
Stackable washer
The washer at the bottom of a stacked pair or a single-frame laundry center, repaired inside the closet or recess it was sized for.
In LG's own words
The FE/E04/E12 error indicates a problem with water overfilling.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. LG front-load washers; the current list pairs FE with E04 and E12. LG's older list adds that a machine with a bad inlet valve may fill even when turned off.
LG FE washer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about FE.
Can I clear FE myself?
Should I turn the water off when my LG washer shows FE?
Can FE on an LG washer come from the detergent drawer?
Back to your everyday
Still showing FE?
Book with the code as it appears, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.